# =============================================================================
# config.py - Temperature/Humidity (SHT30) monitoring module (Pi 4 Model B) config — non-secret defaults
#
# Operational/secret values such as server URL / API_KEY / device identifiers (DEVICE_ID/LOCATION)
# are loaded from config_local.py. config_local.py is excluded from commits via .gitignore.
#   Setup:  cp config_local.example.py config_local.py  → fill in the real values
#
# This module is "Module 2" (temperature/humidity). The server (php/) dashboard shows sensor_id=2 as the
# default temperature/humidity sensor, so the SENSOR_ID default is set to 2.
# =============================================================================

# ─────────────────────────────────────────────
# Sensor identity (for server dashboard display; not secret)
#   SENSOR_ID is the key in the server's leak_sensor_metric / leak_sensor_status. Dashboard default chart=2.
# ─────────────────────────────────────────────
SENSOR_ID = 2
SENSOR_NAME = "Sensor 2 (SHT30)"

# ─────────────────────────────────────────────
# I2C bus config (Pi 4 40-pin header)
#   SDA = GPIO2 (physical pin 3), SCL = GPIO3 (physical pin 5) → I2C bus 1
#   ADDR pin: GND=0x44, VDD=0x45
# ─────────────────────────────────────────────
I2C_BUS = 1
I2C_ADDR = 0x44

# Force simulation. If True, runs with dummy measurements without hardware (for server integration checks).
# Even if False, the driver auto-falls back to simulation when smbus2 is not installed / I2C is disabled.
FORCE_SIMULATION = False

# ─────────────────────────────────────────────
# Measurement/report intervals (same defaults as firmware app_config.h)
# ─────────────────────────────────────────────
REPORT_INTERVAL = 3600       # Normal measure/report interval (seconds) = 1 hour
                             # Server offline detection must exceed this: METRIC_HEARTBEAT_TIMEOUT_SEC
                             # (default 7500s ≈ 2 missed hourly reports + margin) covers it.
                             # Override per-node in config_local.py if a different cadence is needed.
MEASURE_RETRY_DELAY = 5      # Wait before retry after a failed measurement (seconds)

# ─────────────────────────────────────────────
# Physical plausibility range for temp/humidity (same as firmware classify_metric_status)
#   Values outside this range are reported as metric_status="out_of_range".
#   * Operational threshold judgments (high/low temp, high/low humidity) and SMS are all handled
#     by the server (config.php METRIC_*). This module only faithfully reports measurements.
# ─────────────────────────────────────────────
TEMP_LOW_C = -40.0
TEMP_HIGH_C = 125.0
RH_LOW = 0.0
RH_HIGH = 100.0

# Module identity version (server app_version field; the server only records it, does not validate)
APP_VERSION = "v2606-sht30-rpi4"

# ─────────────────────────────────────────────
# Logging config
# ─────────────────────────────────────────────
LOG_FILE = "/var/log/sht30_sensor.log"
LOG_MAX_BYTES = 5 * 1024 * 1024  # 5MB
LOG_BACKUP_COUNT = 3

# ─────────────────────────────────────────────
# HTTP retry config (same defaults as firmware APP_HTTP_*)
# ─────────────────────────────────────────────
HTTP_TIMEOUT = 10            # Single request timeout (seconds)
HTTP_RETRY_COUNT = 3         # Number of retries
HTTP_RETRY_DELAY = 5         # Wait between retries (seconds)

# ─────────────────────────────────────────────
# Load operational/secret values (fail closed)
#   If config_local.py is missing, abort immediately with a clear error instead of
#   starting incorrectly with placeholder/hardcoded secrets.
# ─────────────────────────────────────────────
try:
    from config_local import (   # noqa: F401  (sht30_sensor.py re-imports from config)
        API_URL,
        API_KEY,
        DEVICE_ID,
        DEVICE_LOCATION,
    )
except ImportError as e:
    raise RuntimeError(
        "config_local.py not found. "
        "Run `cp config_local.example.py config_local.py`, then fill in the real server URL / API_KEY / "
        "device info. (Never commit secret values.)"
    ) from e

# ─────────────────────────────────────────────
# Optional override — per-device values from config_local.py.
#   Editing the tracked config.py per device causes deployment drift, so a co-located
#   node (e.g. a leak node reporting temp/humidity under the SAME sensor_id 1 or 3)
#   overrides SENSOR_ID / SENSOR_NAME here instead. If config_local defines neither,
#   the defaults above (SENSOR_ID=2) are kept — backward compatible for Pi-B.
# ─────────────────────────────────────────────
try:
    from config_local import SENSOR_ID  # noqa: F811 — per-device sensor_id override
except ImportError:
    pass
try:
    from config_local import SENSOR_NAME  # noqa: F811 — per-device display name override
except ImportError:
    pass
try:
    # Per-device report cadence. Leak-node co-sensor (id 1/3) reports every 600s (10 min)
    # to match the leak node's cadence; the standalone Pi-B (sensor2) keeps the 3600s (1 h) default.
    from config_local import REPORT_INTERVAL  # noqa: F811 — per-device report interval override
except ImportError:
    pass

# Validate (fail closed) — a typo must not silently start with a wrong/plausible id.
if not (isinstance(SENSOR_ID, int) and 1 <= SENSOR_ID <= 255):
    raise RuntimeError(f"SENSOR_ID must be int 1..255 (check config_local.py): {SENSOR_ID!r}")
if not (isinstance(SENSOR_NAME, str) and SENSOR_NAME):
    raise RuntimeError("SENSOR_NAME must be a non-empty string (check config_local.py).")
if not (isinstance(REPORT_INTERVAL, int) and REPORT_INTERVAL > 0):
    raise RuntimeError(f"REPORT_INTERVAL must be a positive int (seconds) (check config_local.py): {REPORT_INTERVAL!r}")